Tag Archive for: bathroom renovation tips

A bathroom can look finished long before it is protected. Tiles, grout and silicone give the room its visible surface, but they are not the waterproofing system. The membrane installed beneath them is what prevents moisture reaching wall framing, subfloors and adjoining rooms. Knowing how to waterproof a bathroom properly helps homeowners understand why this stage deserves careful planning, licensed trade coordination and quality control.

For Sydney and NSW renovations, waterproofing should be treated as a critical construction stage rather than a quick task completed between plastering and tiling. A failed membrane can lead to swollen timber, damaged ceilings, mould, loose tiles and costly remedial work that often requires the bathroom to be stripped back.

Start with the bathroom design and substrate

Waterproofing begins before any membrane is opened. The layout must confirm the locations of the shower, bath, vanity, toilet, floor wastes and any hob or level-entry shower detail. These decisions affect falls to waste, drainage positions, wall junctions and the extent of waterproofing required.

The substrate also needs to be suitable. Floors and walls must be structurally sound, clean, dry and free from dust, paint, oil, loose material or old adhesive. Cracks, sheet joints, penetrations and changes of material need to be addressed before waterproofing starts. Applying a premium membrane over an unstable or poorly prepared surface will not solve the underlying problem.

In an older home, this assessment is particularly important. Water damage may be concealed behind existing tiles or within a timber floor. A builder should inspect the framing, sheeting and plumbing rough-in while the room is open, then repair or upgrade affected areas before the new bathroom is lined and waterproofed.

Get falls and drainage right first

Waterproofing and drainage work together. The bathroom floor needs appropriate falls so water moves towards the floor waste rather than sitting in corners or against walls. In a walk-in shower, the set-down, screed and waste position need to be planned early, especially where a flush threshold is desired.

A membrane cannot compensate for poor falls. If water regularly ponds on the tile surface, it can stain grout, increase cleaning requirements and place unnecessary stress on joints and sealants. Good preparation creates a bathroom that is easier to use as well as easier to maintain.

Choose a compatible waterproofing system

Australian wet-area waterproofing is governed by the National Construction Code and relevant Australian Standards, including AS 3740 for waterproofing of domestic wet areas. The exact system and application requirements depend on the room design, substrate, shower configuration and product manufacturer instructions.

Most residential bathrooms use a liquid-applied membrane, although sheet systems may suit particular details or substrates. The key point is compatibility. Primers, bond breakers, membranes, sealants, tile adhesives and screeds must be selected as a coordinated system where required by the manufacturer.

Do not assume that a thicker-looking coating is better. Waterproofing products are designed to achieve a specified dry film thickness, which may require multiple coats applied at controlled coverage rates. Applying material too thin can leave weak points. Applying it carelessly or without allowing proper curing between coats can also compromise performance.

How to waterproof a bathroom step by step

The process varies between projects, but a compliant bathroom waterproofing sequence generally follows a clear order.

1. Complete the plumbing rough-in

Plumbing pipework, wastes and shower fittings should be positioned before waterproofing. Every penetration through a wall or floor is a potential risk point, so it needs to be correctly detailed with the system components specified for that purpose.

The floor waste must be secure, correctly set and compatible with the membrane detail. If plumbing changes are made after waterproofing, the membrane may need to be repaired and re-certified rather than simply patched without records.

2. Prepare and prime the surfaces

Once linings, screeds or substrates are ready, the waterproofing contractor prepares the surfaces in line with the chosen product system. This can include sanding, vacuuming, filling minor imperfections and applying primer.

Moisture content and curing time matter. Fresh screeds, levelling compounds and cement-based materials may need time to cure before a membrane is applied. Rushing this step can affect adhesion and create failures that do not become visible until months after handover.

3. Reinforce junctions and penetrations

Corners, wall-to-floor junctions, sheet joints, hob edges, wastes and pipe penetrations receive special treatment. These areas move more than broad, flat surfaces and are where many leaks begin.

A bond breaker, reinforcing tape, fabric or pre-formed collar is installed as specified by the membrane manufacturer. It allows controlled movement while maintaining a continuous waterproof barrier. This work is detailed and should never be treated as an optional extra.

4. Apply the membrane to the required areas

The membrane is applied across the floor and up walls in the required wet areas. Shower walls, shower floors, bathroom floors and wall junctions are commonly included, while the height and extent of coverage depend on the bathroom layout and applicable requirements.

For example, a fully enclosed shower, a shower over a bath and a level-entry shower can each require different detailing. The installer should follow the project specification, the relevant standards and manufacturer instructions rather than relying on a one-size-fits-all approach.

Each coat must be applied evenly, with sufficient coverage at corners and around penetrations. The first coat needs to cure before the next is applied. Rushing through this stage to bring tiling forward is a false economy.

5. Inspect, cure and document the work

Before tiles cover the membrane, inspect it carefully. There should be no pinholes, missed edges, damaged sections or weak detailing around the waste and pipe penetrations. Where practical and appropriate to the system, a water test may be used to confirm the integrity of the waterproofed area before finishes are installed.

The membrane must cure for the period required by the manufacturer. Only then should tiling proceed. Keeping photos of the completed waterproofing stage, product details and compliance documentation provides useful protection for future maintenance, warranty matters and property sales.

Tiling is the finish, not the waterproof barrier

Once waterproofing has cured, tiling can begin. Tile adhesive, grout and silicone are important parts of the finished bathroom, but none should be relied on as the primary defence against water. Grout is porous to varying degrees, and silicone joints require regular inspection and eventual replacement.

Movement joints should be installed where required, particularly at changes of plane and around fixtures. A neat silicone bead at wall-to-floor junctions helps manage movement and directs surface water, while the membrane behind it provides the real protection.

This is why coordinating trades matters. The waterproofer, tiler, plumber and builder need to understand the same floor levels, waste locations and shower-screen details. Fragmented trade work can create gaps in responsibility, especially when a leak appears after the room is complete.

Avoid the shortcuts that cause expensive failures

The most common bathroom waterproofing problems are rarely caused by one dramatic mistake. More often, they result from several small shortcuts: inadequate substrate preparation, incompatible products, missed bond breakers, insufficient membrane thickness, rushed curing or unrecorded alterations after the membrane is installed.

Homeowners should also be cautious about waterproofing over unknown existing tiles or damaged linings. This approach can occasionally be viable in limited circumstances, but it depends on the condition of the existing bathroom, floor levels, drainage and the proposed system. In a full renovation, removing finishes and assessing the substrate usually provides a more reliable long-term outcome.

A low quote can be misleading if it does not clearly state who is responsible for substrate preparation, waterproofing extent, certification, tiling interfaces and rectification of defects. Transparent scope documentation is as valuable as the membrane product itself.

Plan for compliance and long-term maintenance

Bathroom waterproofing is part of a broader compliant renovation process. Depending on the scope of work, a project may involve licensed trades, inspections, certificates and approvals. A professionally managed renovation keeps these requirements organised and ensures the waterproofing stage is not hidden behind tiles before it has been checked.

After handover, maintain silicone seals, grout and plumbing fixtures. Repair dripping taps, leaking shower screens and cracked tiles promptly. These visible elements do not replace the membrane, but maintaining them reduces water exposure and helps preserve the bathroom’s finish.

For a renovation that involves changing layouts, moving plumbing or rebuilding floors and walls, working with a coordinated builder such as Home Extension and Renovation helps keep design, trade sequencing, compliance and workmanship under one managed process. The best time to protect a bathroom is while it is open, accessible and being built correctly – not after a hidden leak has already caused damage.